Tube bundles are the core heat transfer components inside a waste heat boiler. In petrochemical plants, chemical production lines, refineries, and high-temperature process systems, the waste heat boiler recovers energy from hot process gas and converts it into useful steam. When the original tube bundle becomes aged, corroded, fouled, cracked, or thermally fatigued, a precisely manufactured replacement tube bundle is required to restore boiler safety, heat recovery performance, and continuous plant operation.

This project is for tube bundles used in waste heat boilers, also described as exhaust heat boilers. The tube bundle is designed for severe operating conditions, with steam-water emulsion on the tube side and converted gas with water vapor on the shell side. Because the shell-side gas is hot, toxic, corrosive, explosive, and fire hazardous, the tube bundle must be manufactured with strict control of materials, welding, dimensions, inspection, and pressure testing.
The process gas composition includes hydrogen, nitrogen, methane, carbon monoxide, carbon dioxide, and water vapor. The hydrogen content is approximately 56–59%, nitrogen is around 19–21%, methane is not more than 0.5%, carbon monoxide is about 10–12%, and carbon dioxide is about 6.5–9% in dry gas. The water content is also significant, with a mole fraction of about 0.4 in the gas. This makes the service demanding from both thermal and corrosion viewpoints.
The shell-side medium flow is very large. Under the design production condition of 1420 t/day, the converted gas flow is about 301,300 Nm³/h for two boilers, or 150,650 Nm³/h for one boiler. Under the current higher production condition, the flow may reach about 370,000 Nm³/h for two boilers, or 185,000 Nm³/h for one boiler. This high gas flow requires a robust tube bundle structure with good flow distribution, low resistance, and strong vibration resistance.
The steam productivity is specified as 109 t/h for one boiler, and the heating surface is approximately 262 m². This means the tube bundle must provide enough heat transfer area to absorb heat from high-temperature process gas and generate steam reliably. The shell-side gas temperature can be up to 1010°C at the inlet and not more than 400°C at the outlet. The design temperature reaches 1050°C on the gas inlet side and 593°C on the gas outlet side, so thermal expansion, tube support, material strength, and welding quality are critical.
On the tube side, the working medium is a steam-water emulsion. The water chemistry requires alkaline control, with pH around 9.5–10.4, phosphate ion concentration around 5–15 mg/dm³, and total iron not more than 1.00 mg/dm³. Proper water quality helps reduce scaling, corrosion, and deposits inside the tubes, which is essential for safe boiler operation.
The tube-side operating pressure is approximately 106.5 kgf/cm², with a design pressure of 118 kgf/cm². The shell-side operating pressure is approximately 32 kgf/cm², with a design pressure of 35.5 kgf/cm². Hydraulic test pressure is specified as 165 kgf/cm² for the tube side and 53.5 kgf/cm² for the shell side, with water testing for 10 minutes. These requirements show that the bundle is designed for high-pressure industrial boiler service.
The tube arrangement includes multiple tube sizes and lengths. For one boiler, the tube bundle includes Ø50 × 3.5 mm tubes with 156 pieces at 6383 mm length, Ø50 × 3.5 mm tubes with 109 pieces at 6883 mm length, Ø25 × 2.0 mm tubes with 156 pieces at 7405 mm length, and Ø25 × 2.0 mm tubes with 109 pieces at 7905 mm length. Accurate tube bending, tube positioning, tube sheet assembly, and dimensional control are important because the replacement bundle must fit the existing boiler shell and match the original process connections.
A waste heat boiler tube bundle must be designed to handle large temperature differences. During startup, shutdown, and load changes, the tube bundle is exposed to rapid thermal stress. If the bundle structure is not strong enough, tube cracking, tube sheet leakage, weld failure, or vibration damage may occur. For this reason, the design should consider thermal expansion, gas flow direction, tube support plates, corrosion allowance, and stress concentration points.
Corrosion allowance is also important. The technical data indicates corrosion allowance of approximately 1.6 mm on the tube side and 3.2 mm on the shell side. This reflects the more aggressive gas-side environment and the need for long-term protection under corrosive and high-temperature service. Material selection should be based on operating temperature, pressure, gas composition, steam-water chemistry, and applicable boiler standards.
For replacement projects, the new tube bundle must match the original boiler design as closely as possible. This includes tube diameter, tube length, tube quantity, tube sheet dimensions, bundle layout, support structure, welding details, pressure boundary dimensions, lifting arrangement, and inspection requirements. Even a small dimensional deviation may cause installation problems during plant shutdown, so manufacturing accuracy is essential.
The manufacturing process normally includes material inspection, tube cutting, tube bending or forming, tube sheet machining, welding, assembly, dimensional checking, non-destructive testing, hydraulic testing, cleaning, marking, and final inspection. For high-pressure waste heat boiler bundles, welding quality and inspection records are especially important because the equipment operates under high temperature, high pressure, and hazardous gas conditions.
Vrcoolertech can manufacture custom tube bundles for waste heat boilers according to technical drawings, process data, existing bundle dimensions, and project standards. The tube bundle can be designed for steam generation, process gas cooling, exhaust gas heat recovery, petrochemical gas cooling, refinery waste heat recovery, and chemical plant boiler repair.
For this project, the recommended solution is a custom replacement tube bundle for a first-stage exhaust heat boiler, designed with approximately 262 m² heating surface, high-pressure steam-water service, high-temperature converted gas service, hydraulic pressure testing, and strict dimensional control. A properly manufactured tube bundle helps restore boiler heat recovery performance, reduce unplanned shutdown risk, and support safe continuous operation in demanding industrial service.